Corel
Scanning Readme Notes
Microsoft Windows NT4 and Scanning
Service pack 3 must be installed on WINNT4 in order
for scanning to work properly.
TWAIN Compatibility
TWAIN.dll's version 1.6.0.3 and Twunk_16.exe\Twunk_32.dll
version 1.6.0.1 must be used. Please note: some scanner software has been
known to overwrite new versions.
Manufacturer's Scanner Drivers
Always use the latest drivers from the manufacturer.
These can usually be obtained from the manufacturer's website.
Free Disk Space
To avoid application instability, ensure that you
have adequate swap file space at the commencement of the scan. If application
instability is still an issue, make sure that TWUNK_16.exe is not running
on your system.
AGFA Fotolook 2.0.8
Version 2.0.8. and earlier is not supported.
Please upgrade to version 2.0.9. or later.
Canon IX-3010
16-bit grayscale depth is not supported.
Canon ScanCraft CS
Please update your driver to 3.0.1a or later.
Casio Digital Camera 16-bit Driver
Pressing Escape when the driver is active will causes
CorelPHOTO-PAINT and CorelSCAN to go into an non-responding mode.
This is common with other bitmap editing applications.
Epson 2.20
The 16-bit driver is not supported. Please
use the 32-bit driver.
When cancelling an image, ensure that the red
error light is not flashing and that the scanner is in its Ready state
before continuing.
Ensure that when Testing the Scanner Driver in
the Configuration Manager, that the Epson scanner is turned on.
Hewlett Packard Deskscan 2.3 and later
The Test Scanner Driver function will fail if you
have an ADF attached to your scanner. Image
shifts from selected area.
Hewlett Packard PrecisionScan Driver 1.0
This driver is not supported.
Microtek ScanWizard 2.30 and later
Time-out problems may be experienced when scanning
at a resolution under 100 DPI. Read the Error.txt that is provided
with the driver.
Kodak DC50 Digital Camera
You cannot keep the manufacturer's user interface
displayed after a scan.
UMAX MagicScan 2.3 and later
The driver is unstable with all TWAIN applications.
Closing this driver in CorelPHOTO-PAINT without
scanning an image and select File-Open may hang CorelPHOTO-PAINT without
warning.
Other:
We are not supporting 4 bit per pixel depths in version
8.
As well, 48-bit scanning is not supported in
CorelSCAN, the image will be converted to 24-bit RGB.
Thumbnail display is not available from CorelSCAN
when run as a stand-alone.
Selection of memory, buffered, and file mode
is no longer available in CorelPHOTO-PAINT.
CorelTWAIN Drivers
Update your Adaptec SCSI Driver to 1.3 or higher.
CorelTWAIN drivers are no longer supported for this version, but can be
used with the following restrictions:
Epson
You cannot use this driver with newer scanner models.
It only functions on the 600C, 800C, and 1000C. It cannot read the
SCSI bus properly. Therefore, you cannot scan with this driver at
all.
Fujitsu ScanPartner Series
Error indicating that " A serious error occurred
and to ensure that there is adequate space." You must reboot and re-installed
this driver.
Hewlett-Packard 32 Bit
Cannot rotate an image 270 degrees. You will
receive an error to free up some memory even though there is enough available.
Cannot cancel a scan; it will still scan the
image anyway.
Cannot scan with an Automatic Document Feeder.
Microtek ScanMaker II/III
Cannot cancel a scan; it will still scan that image
anyway.
Ricoh IS/ FS2/ IBM 2456
Rotation of scanned image produces very poor results.
You cannot rotate an image 270 degrees.
You cannot scan at less than 100 DPI. You
will receive a message stating that an error occurred while trying to create
scan buffers and to free some memory. This happens in Paint 7 as
well.